archerbell5

How to Replace a Saab 9-3 Key The Saab 9-3 has a good variety of appeal to drivers. It has a powerful engine as well as excellent visibility. It has a high safety rating. However, it is crucial to ensure that you have at least two keys working for your vehicle. If you lose just one key, it could be very costly to buy a new one. How to replace the ignition Key in the Saab9-3 If your car key won't start in the ignition and you want to replace it, you'll need to replace it. This guide will explain how to replace the ignition key on the Saab 9-3. You will need to replace the key, purchase a new reprogrammable cell, and purchase a new case for your key-fob. Modern Saab models employ transponders instead of a traditional key to unlock the car and then start it. The reprogrammable batteries inside the key-fob eventually wear out, and they can't hold any charge. This is especially when you use the same key for the same lock. The good news is that it can be replaced quite easily by an experienced locksmith. If you have the proper tools, and a little patience you can do it yourself. The first step is to remove the key-fob off. This is done by inserting a flathead screwdriver in the slot that is located in the middle of the case. You will need to work slowly, as the plastic is extremely thin and can be damaged easily. After the case is opened, you can make the new key by combining the lower portion of the old key along with transponder and banana. This will ensure that the new key is properly connected to your CIM and can make a significant difference when replacing the sole key for your Saab 9-3. How do I replace the ignition Key in a Saab 900 If you don't have two keys, you'll need to remove the dashboard and steering wheel to gain access to the ignition. Start by disconnecting your negative battery cable. After the battery has been disconnected, you can take off the dashboard and trim pieces around the steering wheel. Once the dash has been removed, you can place an opening with a screwdriver behind the ignition switch. The ignition cylinder is equipped with a key lock, which can stop the vehicle from starting if it does not have the key in it. If saab 93 key isn't working properly, you should check whether the key is inside the lock or stuck within the ignition barrel. It's also an excellent idea to rotate your keys frequently and keep them clean so that one doesn't become bent. Saab cars are different from other vehicles in that they don't have traditional metal keys. The car instead recognizes the electric signals from the key fob via the use of a specific microchip. If you lose only one working key fob, the dealer will charge you top dollar to replace your computer module (known as the CIM). However, we can reprogram your existing computer's EEPROM and set it to accept new keys without replacing it. This will save you over 50% of what the dealer charges! This is the SAAB Key PROGRAM. Find out more information about it here! How to replace the ignition Key on a Saab 9-5 The metal part of a traditional Saab key is simple to copy, and is not a major obstacle against vehicle theft. The real security comes from the electronic part in the key-fob, which has a chip inside that can recognize your vehicle when it is inserted into the ignition switch. Saab has relied on the technology of this anti-theft device for over a decade. It's not as efficient as a door lock however it makes stealing your car a lot more difficult. This is the reason why every Saab owner should always have a spare key on hand. The majority of new Saabs come with two keys. However, they can be purchased from a dealer using a special handheld device called a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception to this rule is NG 9-3 vehicles, that have more modern, more advanced features that require an ignition key. If you lose all keys, the dealer will replace your CIM or TWICE modules and charge you an additional fee for it. But we can reprogram the EEPROM in your existing computer and set it up to accept new keys, without replacing the expensive modules. How to Replace the Ignition Key on the Saab XC90 It's probably time to replace your SAAB key fob if it is experiencing issues turning the barrel of the lock. The process is fairly simple and you don't even need to visit a dealer. You can complete the process at home, using a couple of basic tools. In the beginning, you'll need to prepare the new key. Before you start, disable the anti-theft feature by placing blocks under the rear wheels and activating your handbrake. Insert the key into the ignition and then turn the key to the “on” position. This will activate the accessories, but it will not start the engine. Repeat this five times and leave the key in the on position. Then you'll need to buy an additional case for your key fob. These are available at most auto parts stores and are typically very affordable. Depending on the model, you can even purchase them without electronics. To open the case simply push the screwdriver with a flathead into the slot in the middle. After you have split the case, you will have access to all the internal electronic components. To remove the electronics employ a small screwdriver and try prying them out in a gentle manner.